Home > Post Error > Post Error 1787 Proliant

Post Error 1787 Proliant

The HP utility doesnt give the option for configuring a spare drive now - as was shown in the HP documentation about this. Not the answer you're looking for? I do not have any drives that are amber. Select F1 to continue – drive array will remain disabled. http://spamdestructor.com/post-error/post-error-1787.php

The system returned: (22) Invalid argument The remote host or network may be down. Please try the request again. F2キーを押して、応答しないドライブを無効にします。 b. 故障したドライブを交換します。 F1キーを押してコントローラ上のすべての論理ドライブを無効にした状態でシステムを起動します。 システムの電源投入および切断は、必ず、正しい手順で行ってください。 • システムに電源を投入する際は、すべての外付ストレージ システムの電源を入れてからサーバの電源を入れ なければなりません。 • システムの電源を切断する際は、サーバの電源を切ってから、外付ストレージ システムの電源を切るように しなければなりません。 関連情報 » HP ProLiantサーバ トラブルシューティング ガイド » HP ProLiant サーバー - アレイコンフィギュレーションユーティリティ (ACU) からアレイ診断ユーティリティ (ADU) レポートを取得する方法 » HP How do I replace and (&&) in a for loop?

The failed drive has been marked as failed and replaced with one of the unassigned drives in the same slot but the replaced drive is not being rebuilt. Select F2 to continue without starting Automatic Data Recovery. Test and replace defective cables. 2. To print the manual completely, please, download it.

GB physicaldrive 2:2 SCSI Bus: 2 SCSI ID: 2 Status: OK Drive Type: Data Drive Interface Type: Parallel SCSI Transfer Mode: Ultra 320 Wide Size: 146.8 GB Transfer Speed: 320 MB/Sec Their last firmware updates occurred in 2008. –ewwhite Jan 6 '13 at 22:34 @user151520 I imported your data into the question. –sysadmin1138♦ Jan 8 '13 at 1:50 The 2 unused drives should have been setup as spares in hindsight. By using this site, you accept the Terms of Use and Rules of Participation. End of content United StatesHewlett Packard Enterprise International CorporateCorporateAccessibilityCareersContact UsCorporate ResponsibilityEventsHewlett Packard LabsInvestor RelationsLeadershipNewsroomSitemapPartnersPartnersFind a PartnerPartner

Replace drive X. (depending on the fault-tolerance level, all data may be lost if another drive fails). 3. 1788-Slot X Drive Array Reports Incorrect Drive Replacement... ...The following SCSI drive(s) should I believe that the hot spare is configured when the first building the array. If it is, then it means that you won't be able to rebuild the array due to read errors on the remaining RAID 5 disks. https://community.hpe.com/t5/ProLiant-Servers-ML-DL-SL/POST-Error-1787/td-p/2619708 Select F2 to reset configuration – all data will be lost.

The system returned: (22) Invalid argument The remote host or network may be down. Does using Mold Earth to trip someone break its rule against causing damage? Thesis reviewer requests update to literature review to incorporate last four years of research. Otherwise it showed the same info as previous (still 2 unassigned drives) –user151520 Jan 6 '13 at 20:05 add a comment| up vote 0 down vote The unassigned drive has controller

Showing results for  Search instead for  Do you mean  Menu Categories Solutions IT Transformation Internet of Things Topics Big Data Cloud Security Infrastructure Strategy and Technology Products Cloud Integrated Systems Networking https://h20628.www2.hp.com/km-ext/content-webapp/document?docId=emr_na-c02735164 Select F1 to continue – drive array will remain disabled. Why did they bring C3PO to Jabba's palace and other dangerous missions? Got it, continue to print 2012-2016 ManualsLib.com About Us About ManualsLib Privacy Policy F.A.Q.

What do you call "intellectual" jobs? navigate here Don't show me this message again. Browse other questions tagged hp hp-proliant hardware-raid raid5 hp-smart-array or ask your own question. share|improve this answer answered Jan 6 '13 at 21:05 Martino Dino 835613 Bad advice, at least until we get the status of the drive array.

Show all Bl35p Bl40p Bl460c Bl480c Bl680c g5 Dl560 Dl590/64 Dl740 Ml310 Ml330 Ml570 Comments to this Manuals Your Name Enter your comment: Symbols: 0 Enter text from picture: Write a Restore password × Upload manual upload from disk upload from url Thank you for your help! The two remaining drives show up as unassigned in the Array Configuration Utility. http://spamdestructor.com/post-error/post-error-1787-drive-array.php More Info Sign In Upload Page of 139 Go Download Table of ContentsContents TroubleshootingTroublesh..

Action: If replacement drives are installed in the wrong bays, properly reinstall the drives as indicated and: Press the F1 key to restart the server with the drive array disabled. troubleshooting guidepage 1................................................................................................................................................................ Automatic Data Recovery Previously Aborted!... ...The following SCSI drive(s) need Automatic Data Recovery: SCSI Port Y: SCSI ID Z Select F1 to retry Automatic Data Recovery to drive.

I did remove the drive marked as failed and replaced it with one of the unassigned drives but this didnt appear to make any difference at all based according to the

more hot questions question feed about us tour help blog chat data legal privacy policy work here advertising info mobile contact us feedback Technology Life / Arts Culture / Recreation Science I admit I should have ideally set the hot spares when the array was created - am now learning the hard way. How do fix this? Press the F2 key to use the drives as configured and lose all the data on them.

F1 will let the the server start but it is running slow.It's a standard system so without having access to documentation or the original PO I am assuming that it has Action: • Perform one of the suggested actions: • Press the F1 key to retry Automatic Data Recovery to the drive. Do I have to physically disconnect the cable inside the box? 0 Kudos Reply All Forum Topics Previous Topic Next Topic The opinions expressed above are the personal opinions of the this contact form If the hdd was larger, it would not utilize the additional space.