Home > Post Error > Post Error 1794-slot X Drive Array

Post Error 1794-slot X Drive Array

Mitch September 18, 2012 at 5:52 pm Hey Ted, I had/have the same fear about getting the OEM batteries. I have 3 drives and 1 is faulty. For information, both servers are on the same sub-network.   Any idea ? Good luck! http://spamdestructor.com/post-error/post-error-1784-drive-array-drive-failure.php

Merlynoz January 5, 2013 at 3:50 am I have a HP ML350 server, the Array E200i on the motherboard failed so I had to replace the motherboard. Than also it is give same error. I published an article explaining how HP calls RAID 1 a subset of RAID 10 just yesterday. 0 Pimiento OP mohammedsalehdhunnoo Aug 31, 2016 at 8:50 UTC 1st Post I Help Desk » Inventory » Monitor » Community » ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection to https://h20565.www2.hpe.com/hpsc/doc/public/display?sp4ts.oid=3949980&docId=mmr_kc-0117751&docLocale=en_US

Upon boot the P400 controller reported error codes 1794 - Array Accelerator Battery Charge Low and 1786 - Slot 1 Drive Array Recovery Needed...The following disk drive(s) need Automatic Data Recovery: Port 1I: Box If the battery isn't charging then you would continue to get these errors. Its very important know that the battery is good, in some cases I probe it in other similar server, and I check that charge ok If the battery and the memory

thank you Mitch July 16, 2013 at 2:44 pm Hmm..all I can suggest is to check and see if it is the latest version of SMH. The symptoms such. Thanks in advance! SEARCH TIP : For hints on locating similar documents on HP.com, refer to the Search Tips document .

Adam April 5, 2010 at 1:09 pm Looks like the firmware update actually worked. HP now says we need to replace the cache module. As the server does not complete POST and there is no display, you may attempt the following troubleshooting steps to help isolate the issue:   a. Locate the system maintenance switch (SW1)) on the system board using the server's Maintenance and Service guide, Component identification > System board components, item 19.

Available Categories Select a category to browse . We’ll see if it sticks. Roman October 14, 2013 at 7:33 am Mitch, we have a lot of servers HP DL360 G5 with Smart Array 6400. After few seconds i hear some few click sounds from behind the server, power button goes amber and server reboots.

I have heard of what you describe happening with some early versions. https://h20565.www2.hp.com/hpsc/doc/public/display?docId=mmr_kc-0101966 We have restart SMH services from Windows, but still could not come up. HPSIM is no longer reporting an error. Click the Kudos Star!I try everything but I do what I can. 0 Kudos gregersenj Honored Contributor [Founder] Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email

on the OS?

0 0 03/03/15--23:47: Re: DL380 G3 failure Contact us about this article Hello,   Have you tried to boot the server with just two sticks of RAM navigate here Page 38 of this manual has instructions. I have replaced hundreds possibly thousands of these batteries in my time and the minimum I do is to have the server in standby mode for P400/P410 type SA controllers but I replaced the new cache module and battery of 3 sets but problem exists and i tested the new cache modules in another server also but problem not solved.

Claim or contact us about this channel Embed this content in your HTML Search confirm cancel Report adult content: click to rate: Account: (login) More Channels Showcase RSS Channel Showcase 5265608 We will be very grateful for any advice.   Regadrs, Ildar

0 0 03/03/15--01:51: HP Proliant DL 380 G7 Contact us about this article how can i get the hp Definitely check the batteries first, my preferred way is to use a multimeter. Check This Out My server is in use, and I don't have enough slack in the cables to open the case while it is running.

If it's good then think about replacing the entire BBWC module. If the issue persists, then removing the power cable from the server and power source, remove all installed expansion cards, all memory modules except that installed in DIMM slot A3 for If iLO has been configured, then login to iLO, click IML logs at the left hand side and check for any hardware related error messages.   b.

Some even show it as part of a whole assembly.

untung July 11, 2013 at 9:09 pm hi mitch, we have replaced it with the new controller, smart array 6400. Any clues? Smart Array Controller Troubleshooting Resources (User Guide) Configuring Arrays on HP Smart Array Controllers Reference Guide (see Diagnosing Array Problems) http://bizsupport2.austin.hp.com/bc/docs/support/SupportManual/c00729544/c00729544.pdf (User Guide) HP Smart Array Controllers for HP ProLiant Servers Photos attached.

You mentioned you had already applied firmware updates…which one actually worked for you? FBWC capacitors discharge more quickly than BBWC batteries when power is removed from the server. Sign up for Subscriber's Choice at the following URL: http://www.hp.com/go/myadvisory NAVIGATION TIP : For hints on navigating HP.com to locate the latest drivers, patches, and other support software downloads for ProLiant http://spamdestructor.com/post-error/post-error-1797-drive-array-array-accelerator-read-error-occurred.php As long as the case doesn't look like it will rupture and cause trouble then I might consider it.

I don't know what to do next?? Mary August 23, 2012 at 4:12 am Hello Prajapati: Update the firmware of the smartarray is the first step, the second, change the battery, if this dont fix the problem you Do i will need to do some configurations after i reset NVRAM? They are sourcing a replacement drive (and an additional hot-swap spare) ASAP.

Please try the request again. Mount ISO 2. Make sure you have the latest updates for your SCSI drives before you update the Array firmware though or else you will get more errors in POST. Is it possible to access the data by moving the HDD in the G4 server in the same order of SCSI ID and booting from DVD?

Powered off the server for 5-10 minutes to let it "cool down", started it back up, and entered the P400 config via F8. Is it normal that when i turn on server and there is no ethernet cable inserted in NIC #1, front panel NIC light is turned on? They were able to charge it, so it appears it was a faulty cache module that caused the problem. Thanks Mitch July 2, 2013 at 6:12 pm That is the correct Part#.

Because the only idea for me is that the bateries are bad, old I dont know.