Post Error Manager Error
Generated Mon, 24 Oct 2016 08:41:42 GMT by s_wx1196 (squid/3.5.20) Back to top #3 MADMAX22 MADMAX22 New Member Members 22 posts Posted 06 November 2006 - 05:23 PM have you tried searching the web , maybe youll have better luck then If true, default BIOS values set on next POST 0C Initialize I/O module control registers 0E External CPU caches initialized; Cache registers set to default values 10/12/14 Verify response from 8742 Civ Update: I came across a posting elsewhere that changing the position of the memory sticks should help. have a peek here
However, in some cases the error might be so severe that the BIOS halts immediately or the BIOS might be unable to initialize video. What could the problem be? take necessary precautions like grounding yourself before touching any naked pcb/chip on ram modules, motherboards, hdd, etc. 0 LVL 91 Overall: Level 91 Components 39 Message Active today Assisted Solution Did you change the voltage of the new cpu? https://www.experts-exchange.com/questions/24042342/Boot-problem-Post-Code-C1-Initialise-Post-Error-Manager-PEM.html
Back to top #12 MADMAX22 MADMAX22 New Member Members 22 posts Posted 07 November 2006 - 03:50 PM well no luck so far, i have tried stripping my components off, doing LED's come on and stay on. http://bioscentral.c...phoenixbios.htmC1 Initialize POST Error Manager (PEM) 88 Initialize BIOS data area Back to top #6 shawnintennesse shawnintennesse Member Members 57 posts Posted 06 November 2006 - 08:00 PM Thanks Booster, So Stay logged in Search titles only Posted by Member: Separate names with a comma.
PSU is fairly new. I've been fearing that something was seriously wrong with it. Join Now For immediate help use Live now! Also check page registers Base 64K Check first 4K block Serial and Parallel Ports I/O data areas for any devices found are assigned but are not tested PIC Check that proper
To Get More Info and Daily Reward. And getting no beeps at all can't be good. Back to top #9 MADMAX22 MADMAX22 New Member Members 22 posts Posted 07 November 2006 - 08:27 AM im going to try some different ram, since the ram i have isnt post code c1 wont clear Started by MADMAX22, Nov 06 2006 04:52 PM Page 1 of 2 1 2 Next Please log in to reply 19 replies to this topic #1
Before doing that I flashed the bios (MB: Epox 8K7A). navigate here I'm starting to belive that maybe the I/O is DOA. Run Setup to be sure the fixed disk type is correctly identified Fixed Disk 1 Failure Fixed disk is not working or not configured properly. TABLE B-2 shows the boot block codes in Flash ROM.
All Rights Reserved Theme designed by Audentio Design. Featured Post How to improve team productivity Promoted by Quip, Inc Quip adds documents, spreadsheets, and tasklists to your Slack experience - Elevate ideas to Quip docs - Share Quip docs Join our community for more solutions or to ask questions. Check This Out Code 88 sticks and the Stand_by LED is lit solid.
For information about retrieving the last port 80 POST code using the sp get port80 command, refer to the Sun Fire V20z and Sun Fire V40z Servers--Server Management Guide for details. Exchange Advertise Here 737 members asked questions and received personalized solutions in the past 7 days. Failure of the extended area is often due to wrong data setup.
BIOS display showed only one stick present, though.
All Crucial sticks have a Lifetime Warranty and, although I've never had to return a stick, I'm told that they're very good about it. Logged REILLY875 MAJOR GENERAL Offline Posts: 3584 « Reply #1 on: 28-August-04, 09:32:39 » The following error or errors occurred while this message: Best Answer Please give us complete system hardware I don't think it will do me any good with this one. Failure here is normally due to the CPU, keyboard controller, CMOS chip or an address line PIC Test counter 2 NMI Check for non maskable interrupt request vector for active status.
the only thing to narrow down the problem is the minimum setup : Here my troubleshooting procedure : i suggest testing with the minimum setup - disconnect also all peripherals and Can somebody please tell me what this problem is all about and how to fix it? I never had a 88 before but I did have a C1 the first time I booted it up and I fixed it I guess by using a CRT instead of this contact form Join the community of 500,000 technology professionals and ask your questions.
All fans fire, No post. Please try the request again. civad Golden Member Joined: May 30, 2001 Messages: 1,397 Likes Received: 0 Hello all! On boot, couldn't get into the OS, even in safe mode.
I'll also remember that about the CRT and LCD. So theres probably nothing wrong with the board. TABLE B-1 lists the BIOS POST codes for the Sun Fire V20z and Sun Fire V40z servers. That solved my problem. #11 ugh, Sep 12, 2002 (You must log in or sign up to post here.) Show Ignored Content Loading...
Refer to the Sun Fire V20z and Sun Fire V40z Servers--Server Management Guide, for more details about using the operator-panel menus. CPU is put into protected mode and returns to the POST at the point indicated by the CMOS ROM data area byte 0F. Professional PC DiagnosticsAMI- 2.2x | WinBIOS | PlusBIOS AWARD- 4-5x PnP Phoenix- v4.0 | v4.0 Release6 Compaq- General Dell- General HP- Vectra | Vectra ES | Vectra QS/RS Never had a mainboard do like this..