Home > Precor Error > Precor 9.31 Error 42

Precor 9.31 Error 42

Contents

Question about Precor Elliptical Trainers 1 Answer Received err 42 on my ...Error Code 42 Error Code: 42 Manufacturer: Precor Model: All Models Error Description: Error 42, Lift Position Value Out The system returned: (22) Invalid argument The remote host or network may be down. Inspect the lift potentiometer connector and repair connection if necessary. Unit is in remote location have not been able to get visual or repair, pre planning trip. http://spamdestructor.com/precor-error/precor-efx-5-25-error-42.php

Posted on Sep 27, 2011 Helpful 0 Not Helpful Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images Add Your Answer Tips for a great Precor 935 Premium Series... 3 Answers Precor M9.21 Treadmill - Stops under load Precor 9.21 Treadmill 4 Answers My Precor 9.35 treadmill keeps shutting off. It is possible to see this message displayed intermittently due to external causes. Typically on the Precor Treadmills if there are errors on the unit, you can press and hold the stop button for 3-5 seconds and it will go into the error log.

Precor Treadmill Error Codes

Inspect the lower PCA (if unit is 120 VAC/ Version 2) for jumper. Precor Treadmills precore error 40 know treadmill motor bad treadmill error 40 investigate definition approaching definition definition pre physical change definition positive number definition replacing controller treadmill View Less » 145 Recommended Action: Determine the amount of AC input current being drawn by the unit under no load and loaded conditions using a clamp on AC ammeter. Recommended Action: Intermittent connections can be difficult to locate.

I cant start a workout because the second things get going the screen pops up saying 'error 42'. Precor Error Code 44 Jan 04, 2011 | Precor C956 Treadmill with Cardio Theater... Only re-calibrating the lift motor will not solve the problem. Precor Error 82 Typically it can be identified and tracked using an ohmmeter.

MVP: An expert that got 5 achievements. Your cache administrator is webmaster. solution? http://www.fixya.com/search/p1141705-precor_efx_546i_elliptical_version_4/error_42 A lift calibration number of 0 or 255 indicates an open or shorted potentiometer connection.

Inspect the lift potentiometer connector and repair connection if necessary. Precor Error 22 If the intermittent connection cannot be found or corrected, replace the lift motor. Replace the interconnect cable if necessary. Lift Position Value Out of Range Precor Error 42 Sep 13, 2012 | Precor 9.31 Treadmill 1 Answer SPEED ERROR ON PRECOR 927 TREADMILL I had the speed error on my

Precor Error 15

Typically it can be identified and tracked using an ohmmeter. http://www.ehow.com/how_5519820_reset-error-code-precor-treadmill.html The lower PCA is bad. Precor Treadmill Error Codes Or just drag it here! Precor Treadmill Error 29 Repair or replace wiring connections as necessary.

Failures causing these error messages to be displayed are rare. this content Re-measure the no load AC input. If the Error 42 condition is intermittent, a connection issue is probably the cause. A lift calibration number of 0 or 255 indicates an open or shorted potentiometer connection. Precor Error 40

Precor 9.21 Treadmill 1 Answer What is an Error 22, 23,and 26 on a precor 9.35? The lower PCA is bad. In this case, the Error 42 is a secondary symptom and the issue should be approached as an Error 40. http://spamdestructor.com/precor-error/precor-efx-546-error-42.php Investigate for cause and correct.

Corrective Action Bad or intermittent connection of the lift position sensor (potentiometer) is the most common cause of the error 44. Precor Treadmill Error Code 82 This means the problem could be anywhere between the lift motor and the upper PCA. Precor Error 15, AC Input Voltage Too High Probable Cause 1.

Both windings must be checked on an AC lift motor.

Inspect all wiring and connections related to the lift position sensor (potentiometer). Rafael Andrade/Demand Media Step 4To view the treadmill's odometer reading when a particular error code was elicited, press "SELECT" while a particular error code is displayed. Replace the lower PCA if necessary. Precor Lower Pca Electrically isolate the inductor from the drive motor circuit.

Recommended Action: Intermittent connections can be difficult to locate. Or just drag it here! Simply recalibrating the lift motor will not solve the problem.] If the lift calibration number is not 0 or 255 and does not change when the lift motor turns, replace the http://spamdestructor.com/precor-error/precor-error-40.php See all Precor C956i Treadmills with HR / WholeSale Questions Related Topics precor hr error Treadmills c9 error precor error 42 precor error 40 precor manuals precor error 40 code true

Using an ohmmeter, the fuse should measure 1 ohm or less. The high power demand is caused by a shorted or de-magnetized drive motor. This is definitely true if the Error 42 occurred while the lift was within its normal physical range. The upper PCA is bad.

Using the appropriate service manual for the unit being tested, refer to the lift calibration procedure. Precor Error Code 42 Error Code: 42 Manufacturer: Precor Model: All Models Error Description: Error 42, Lift Position Value Out of Range. If the intermittent connection cannot be found or corrected, replace the lift motor. This means the problem could be anywhere between the lift motor and the upper PCA.

Using the appropriate service manual for the unit being tested, refer to the lift calibration procedure. Add × Loading... Not finding what you are looking for? These same readings should be taken on a like unit, in good operating condition with a know good deck and running belt.

Not sure where they came from, hopefully not another problem. From what I have read on Error 2's it could be a upper PCA issue, or possibly a dip in AC input during the power up sequence.Treadmills require a dedicated line, Using the appropriate service manual for the unit being tested, refer to the lift calibration procedure. If anyone else has the speed error it might be worth a look to see if its the same problem.

A lift calibration number of 0 or 255 indicates an open or shorted potentiometer connection.