Home > Printer Error > Printer Error 13.2

Printer Error 13.2

Same as error 51. 2686/D Only: 1. Replace Laser/Scanning Assembly. 4. Suggestions welcomed. Trying to print envelope in duplex mode (envelopes cannot be duplexed). this content

Do not attempt to do this from the top to bottom as you could break the feed sensor flag. Upon powering on your problem should be resolved. Install the replacement fuser by inserting it and aligning the left side first. Sign in to report inappropriate content.

Hopefully it will force the stuck paper up to where you can grab and remove it. Replace Interface/Formatter PCA. Replace PS1 if defective. 2. A case like this could easily cost hundreds of thousands of dollars.

  • Sign in Share More Report Need to report the video?
  • Reseat connectors J002 on the DC Controller and J601 on the LaserDrive PCA. 4.
  • Out of spec media. 3.
  • Replace High-Voltage Power Supply. 20 ERROR/MEM OVERFLOW/INSUFFICIENT MEMORY 1.

a. Check paper pickup rollers. so when you go to look at the sensor it will be back in the home position. Another option is to take the MP pick up assembly off and clean out the paper path to make sure all the debris is cleared out.

The message, like a bad penny, refuses to go away. Charlie Warren 27,958 views 12:28 Laser printer shootout (2008) - Duration: 8:22. don't be surprised if you get toner all over your clothes the next time around. http://www.printertechs.com/printer-troubleshooting/370-13-20-error-on-hp-laserjet-4200-or-hp-laserjet-4300-series Often, though, it's a paper jam in the front of the machine.

Replace cable, AC Power Module to DC Controller, connector J208. (P/N RG1-0912-000.) IIP, IIP+, IIIP Only: 1. Optional I/O card is not connected to an active LAN. 3. Top cover open. 2. Set the output bin cover aside.

Home Page Technical Resources Lexmark Error Codes HP Error Codes Tech Support Blog HP Drivers Lexmark Drivers Terms & Conditions Product Conditions Definitions Web Order Minimum Returns Shipping Freight http://fixyourownprinter.com/posts/16075 If it run ok, you have a problem with the pickup assembly behind tray 1. A. Bad registration sensor or bad fuser exit sensor.

My printer prints 100 page with no problem at all, when I want to print the next 100 pg he gave me a paper jam error 13.06, i remove the paper, http://spamdestructor.com/printer-error/printer-error-58-04.php but error message persists. Now I would take that file folder and feed it up the paper channel slowly from the bottom until I see if appear at the top in front by the registration Check DC Power Supply voltages or replace DC Power Supply. 3.

At least one of two tabs must be present. 3. Replace Formatter PCA. 4. Bad cassette microswitch. 2. have a peek at these guys Re-install the plastic rear output bin.

What I have been told to do is check the sensors in case they are defective or have been blocked. Replace Laser/Scanner Assembly. 3. Register now!

a.

Retest. Site Changelog Community Forum Software by IP.Board Sign In Use Facebook Use Twitter Need an account? Check Drum Sensitivity microswitches. Check PostScript ROMs. 40 ERROR (DATA TRANSFER ERROR) 1.

Conection has been broken between printer and EIO/MIO card; try reseating EIO/MIO card 40.X Mio Error 5Si Only: 40.1 HP Mio port 1 (upper slot) 40.2 HP Mio port 2 (lower External fuser access door not closed. 4P/5P Only: 1. No toner cartridge. 3. check my blog Cycle power. 4.

Defective Interlock Switch Assembly. 4/4M/4+/4M+ Only: 1. The cardboard acts as a sturdy object to push past the realignment rollers. Respond to this 0 Looking at the back of the fuser, there is a black plastic piece going lengthwise above the white plastic part with the small rubber rollers at the Replace DC Controller PCA. 16 TONER LOW 1.

IID, IIID Only: 1. Sign in to add this to Watch Later Add to Loading playlists... is between 2925J00000 to 3047J999999. (2-diode to 3-diode upgrade corrects static caused problem.) IIP, IIP+, IIIP Only: 1. DC Power Supply malfunction. 2686 Only: 1.

If the fuser does not turn on check SW101. 3. We use some thin sticky back felt. See Service Note 33471-01B if Serial No. Listen for scanner motor starting up and LED 003 on DC Controller to illuminate. 3.

Loading... Check/replace SIMMs. 62.x memory error 4000/4050/4100/5000/8000/8100 only: 62.x where x = Dimm slot, Check/replace DIMMs. 63 SERVICE 1.