Home > Printer Error > Printer Error 53.11.03

Printer Error 53.11.03

Turn on the printer. Release the check button when the Ready, Data, and Attention light are on steady. Each of the following steps is intended to determine whether the 79 error displayed on the printer is the result of a hardware failure. Turn the printer off, and turn it on again. this content

MVP: An expert that got 5 achievements. Press (Select) to enter the MENUS . When the memory starts counting, press and hold the green (Select) button. May need to replace them Oct 22, 2013 | HP LaserJet 4000n Printer 1 Answer HP 4000n spitting out extra toner. http://fixyourownprinter.com/posts/30707

top 54.10 PRINTER ERROR Description There is a problem with the black drum home position sensor. Apr 15, 2009 | Printers & Copiers 1 Answer 53.10 Error "Shut off printer and turn back on" The error points to your memory see below. Perform a cold reset on the printer. Results 1 to 2 of 2 Thread: error 53.11.03 Thread Tools Show Printable Version Display Linear Mode Switch to Hybrid Mode Switch to Threaded Mode 01-29-2008,04:21 PM #1 mkwatis View Profile

Action Press the Cancel Job button. top 58.3 PRINTER ERROR FOR HELP PRESS alternates with TO CONTINUE TURN OFF THEN ON Description A CPU error reading a memory tag was detected. Tell us some more! Press (Select) to select CONFIGURE DEVICE .

You could take the controller board and reseat the dimms. If the error persists, contact HP Customer Care Support. Action Press (Select) to clear the message and continue printing. http://printertechsforum.com/forum/showthread.php?1983-error-53-11-03 If the 49 error returns turn the power off, unplug the power cable, disconnect all network cables, and remove the HP Jetdirect card, memory DIMMs or Flashcards, or any third-party devices

X DIMM Type 1 RAM Y Device Location 1 DIMM Slot 1 2 DIMM Slot 2 3 DIMM Slot 3 4 DIMM Slot 4 ZZ Error Number 0 unsupported memory 1 Turn on the printer. Dec 15, 2010 | HP LaserJet P3005n Printer 1 Answer Error 53.21 hp color 5550 Doesn't specifically mention the 53.21 error this is the closest they come so you will know The display should show SKIP DISK LOAD .

  1. Depending on document sizes and number of users who print to it you may be able to remove the bad DIMM without needing to replace it.
  2. alternates with TO CONTINUE PRESS 68.1 PERMANENT STORAGE FULL FOR HELP PRESS ?
  3. X Description 1 - Beam detect error 2 - Laser error Y Description 0 - No color K - Black C - Cyan M - Magenta Y - Yellow Action Press
  4. The printer will initialize the hard disk and continue its power-on sequence.
  5. If this message persists, contact HP.
  6. Press (Down Arrow) button once.

Wait for the printer prompt to install each print cartridge. http://www.fixya.com/support/t12832544-fix_hp_laserjet_4000n_error_code Before initializing NVRAM, print a Configuration page and a supplies status page to gather the following information: Total page count and color page count Transfer kit count Fuser kit count Serial Perform a cold reset on the printer. If the 79 error disappears after removing all the accessories, start adding the accessories back one at a time to isolate which one is causing the issue.

When the memory starts counting, press and hold the green (Select) button. http://spamdestructor.com/printer-error/printer-error-58-04.php Press (Select). Move to a different memory slot to determine if the slot is bad. When the memory starts counting, press and hold the green (Select) button.

They change as the state of the printer changes. by moe on Jan 13, 2002 at 11:37am Add comment Please sign in to comment 0 im having the same problem and i dont know what to do.someone can help us For example, pressing the CANCEL JOB button will cancel the job. have a peek at these guys When the memory starts counting, press and hold the green (Select) button.

Press (Select). Watch the control panel. Pull paper by both corners to remove it.

I have two new C3147A-ALC double sided sticks from AllComponents and AllComponents tells me this is the correct memory for the HP 5Si.

top 13.12.00 JAM IN DUPLEX PATH X For help press ? But the Rom Dimm is usually bad and needs to be replaced. Turn on the printer. Press (Select).

Wait for the printer prompt to install each print cartridge. Check the HP Jetdirect configuration (print an EIO Configuration page) as well as the computer that sent the print job (driver or network port configuration). 22 PARALLEL I/O BUFFER OVERFLOW alternates If the error persists, contact HP Customer Care Support. check my blog Close the top cover.

Check the link below its from hp 4500 but hp use same error code at his model HP Support document HP Support Center HP Color LaserJet 4500 and 4550 Series Printers... Articles Forum New Posts FAQ Calendar Community Groups Forum Actions Mark Forums Read Quick Links Today's Posts View Site Leaders Who's Online Blogs Advanced Search Forum Printer Forums Hewlett Packard Laserjets and like dmz said make sure its in slot 1 if you can get it to print. Action Press the green (Select) button to continue.

Press PAUSE/RESUME . My guess is you have that setting on your 4000n set to Exclusively, which will then prevent the job from going to a different tray. Press (Select) to select CALIBRATE NOW or QUICK CALIBRATE NOW . If the error persists, contact HP Customer Care Support.

Action Press (Select) to resume printing. Action Turn the printer off, and turn it on again. Press or to step through the instructions. Turn on the printer.

Expand Popular Questions 3 Answers How do I reset hp laserjet p2015dn to factory default HP LaserJet P2015dn Printer 11 Answers Service error 49.4C02 HP LaserJet 4350dtn Printer 10 Answers HP Turn the printer off. 3. The control panel will display SELECT LANGUAGE . Some data will be lost.

The control panel will display COLD RESET . Move to a different memory slot to determine if slot is bad. Status messages . NOTE: For more information and troubleshooting st Login|Contact Us Computer For Online Computer Support, Ask a Computer Technician Not a Computer Question?

Turn on the printer. Whenever the printer is ready, not busy, and has no pending warning messages, the status message READY is displayed if the printer is online. If this message persists, contact an HP-authorized service or support provider. Press (Down Arrow) to highlight PRINT QUALITY .