Home > Printer Error > Printer Error 55.00

Printer Error 55.00

Also, can I get some instructions on putting in the rollers. Remove the printer from any UPS supplies, additional power supplies, or power strips. 2. HP LASER PRINTER 3050, 3052, 3055, 3390, 3392 1. Back back to top How did we do? this content

Replace main motor. On the IIP/IIIP the connections for the high voltage are made on the left side of the printer so you may want to favor that side as you install the cartridge. On the 4/4M/4+ and 5: The print job is to complex, enable page protect from the control panel and from the software. Add Stickiness To Your Site By Linking To This Professionally Managed Technical Forum.Just copy and paste the BBCode HTML Markdown MediaWiki reStructuredText code below into your site. HP Printers Forum weblink

The only solution is to swap the DC controller PCA.Part number is:RM1-8293-000CN My HP Enterprise ProfileMy Verizon Wireless profileIf you found this post helpful then please award it a Kudo (purple This board takes the input from the two sensors and provides info to the DC controller. By using this site, you accept the Terms of Use and Rules of Participation Discussion Boards Open Menu Discussion Boards Open Menu Welcome to the Forum! Turn the printer off/on to attempt to clear or reset the message.

Press Select button to resume printing, some data loss will occur, you will need to add memory or reduce the complexity of the print job. Reseat cables to the laser/ scanner and engine controller. 4. Technicians answer the phone and help customers with printer problems. Is the problem corrected? YES: End. NO: Replace the DC controller PCB.

HP COLOR LASER PRINTER 8500 1. Reply 0 0 « Message Listing « Previous Topic Next Topic » Related Documents HP Printers - Using HP Diagnostic Tools for HP Printers in WindowsHP Printers - After Windows 10 Turn the image adapt and page protect to ON or AUTO either from the control panel or from within HP Explorers Remote Control Panel. 5P/5Si Same as above, Press GO to https://www.orionmarket.com/product_error/13806/HP/HP-CP6015/55.00.00-dc-controller-error/ ERROR 59 Add Memory 4Si/IIISi Not enough memory for PostScript option.

Also verify the configuration through the menus on the printer. If the message persists, replace the ECU[check on board and track,component damaged-burned its fixable]. May not be connected - check cabling - or it may be defective. Back back to top How did we do?

  1. Replace the formatter and/or firmware DIMM. 4.
  2. Replace the duplexer.
  3. You could also have a defective or dirty exit sensor.

Disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize.2. Change the D.C. You can even send us your printer for repair. A broken tooth on one gear is all it takes.

It can also be caused by a defective DC controller. http://spamdestructor.com/printer-error/printer-error-58-04.php controller board. See "DC controller PCA" on page 181. 57.4 Main fan error (F1) 1. Verify that the tabs aren't damaged and that the tray switches located in the printer are not damaged.

You would want to remove accessories like extra paper trays, additional memory, and jetdirect if you have them. Apr 03, 2014 | HP LaserJet M9050 MFP Printer 1 Answer When turning on I receive error 55.00.00 DC Controller error worked by power off and back on. If that fails I usually recommend turning the machine off, unplug the machine and let it sit 20 to 30 minutes. have a peek at these guys John D.

If the problem persists, replace the DC controller PCA. 5. Back back to top How did we do? Defective formatter board. 3.

Recalibrate the D.C controller board and the formatter board.3.

You need to first check the connection between the dc controller and the formatter and if the connection is fine you need to replace the dc controller. NO: Connect the connectors securely. 2. See Tray 2 lifter-driveassembly.5 Replace the dc controller PCA. Improper MIO connection - look at pins on formatter MIO connection reseat card.

RE: 8000DN error 55.A SPinder1 (TechnicalUser) 29 Mar 04 12:28 Thanks for the reply HPWizzard.It has not returned since I posted last, and I dont know who the owner of that You may need to reseat the memory DIMM's or replace the firmware DIMM or formatter board. ERROR 50.XXXX - ERROR 51 (Loss of beam detect) This is a beam detect error indicating a problem with the laser scanner. check my blog ERROR 89 All Printers (except 5L/6L) The PostScript ROM's have bent or broken pins inspect the pins and reseat if necessary Check to see that the ROM SIMM's are in the

Invalid bus timeout.9 Try using a different printer diver or printing a smaller file.10. Back back to top How did we do? Filmmaker: Uploaded 5 video answers. On rare occasions a defective paper control assembly or actuator can cause this problem.

Plug the printer into a wall outlet and see if this resolves the problem. 3. Error 23 I/O Not Ready ALL PRINTERS The I/O card is not accepting data. A buildup of toner on the edges of the tray which slide into the printer can sometimes cause problems. Can also be formatter PCA.

The chip may be missing or defective or contain incorrect information. Respond to this 0 The DC controller is not part of the formatter. Excessive glitches.3.