Home > Printer Error > Printer Error 55.8

Printer Error 55.8

Trying to print envelope in duplex mode (envelopes cannot be duplexed). step.3 Print This plug-and-play 3D printer has a robust build size of 7.8" x 7.8" x 7.5" (20 cm x 20 cm x 19 cm) and is compatible with XYZprinting’s 3D Check that ROMs are in correct location and orientation. 3. Check and reseat connector J010 on DC Controller PCA. 3. this content

Yes, my password is: Forgot your password? Is that the FORMATTER (which I understand is a small circuit board)?If I get a Formatter in the UK (my machine is a US 120VAC one), doesn't the machine run internally SHARE {{referralMemberCoupon}} WITH: FB Wall or eMail - 1 refill filament for 1 friend who purchase with coupon code. - Free refill filament credit will go in 7 business days after Replace Cable, Laser/Scanner to DC Controller cable. (P/N RG1-0908-000) II, IID, III, IIID Only: 1. check here

IIISi/4Si Only: 1. Tab missing on top cover. 5. 220V unit plugged into 110V outlet. is between 2925J00000 to 3047J999999. (2-diode to 3-diode upgrade corrects static caused problem.) IIP, IIP+, IIIP Only: 1.

Paper pickup clutch turning more than once? I'm living and working in London now.THANKS!Johnny - LongJohnSilver 0 That is an internal communications error between the formatter and the controller. Defective display cable, display, or Formatter PCA. 11 PAPER OUT 1. I/O config for the computer or printer is incorrect. 2.

Don't want to have to scrap my workhorse 4050!THE PROB: I'm geting a 55.8 error message on my 4050. II, III Only: If no jam visible: 1. Check tabs on side of toner cartridge. Change product Choose from all HP products Enter product serial number Please wait while we process your request.

Replace Paper Input PCA. 5. step.2 Edit You can then edit the object using our XYZscan software which comes bundled with the da Vinci AiO 3D printer. Check installation of optional I/O card, reseat if necessary. 2. Install new toner cartridge. 2.

  1. First published in serial form in Fraser's Magazine in 1833-1834, it was discovered by the American Transcendentalists.
  2. Please be aware that promotional purchase and credit usage transactions have special refund policy as described below. - must refund ALL items in purchase transaction - credits will be returned, but
  3. Duplex mechanism has failed 70-71 ERROR 1.
  4. Replace Paper Control PCA (Solenoid/Sensor PCB Assembly). 4.
  5. Paper Control PCA malfunction. 3.
  6. If a duplexer is installed, remove it from the back of the printer.
  7. Power Supply (P/N RG1-0906- 000).

Scan Software XYZscan File Type .stl , .das Format OS Support - XYZscan Windows 7 above (for PC) Mac OSX 10.8 above-bit (for Mac) Hardware Hardware Requirements (for PC/Mac) X86 32/64-bit http://www.printertechs.com/printer-troubleshooting/367-50-5-error-on-laserjet-4200-4240-4250-4300-4350 Our high-tech laser sensor technology and our turn-table print bed drastically save you time on getting your very first print started! The formatter is under the slide off cover on the right side of the printer. Bad Fuser Safety PCA. (P/N RG1-0208-030.) Note 2686A/D: Short resistor R250 on the DC Controller to bypass error 50 time delay.

IIP, IIP+, IIIP Only: 1. 53 Error Unit 1 - Replace memory card (top). 2. 53 Error Unit 2 - Replace memory card (bottom). http://spamdestructor.com/printer-error/printer-error-58-04.php Replace DC Controller PCA. 2. Replace Laser Diode Assembly. 3. Seems that HP has changed the memory spec from the 4000 to the 4050, to the 4100, so what works in one will not work in the other.I configured the printer

Replace Formatter PCA. 3. Short the pin closest to the front of the printer. (The printer must be turned off.) II, IID, III, IIID Only: 1. II, IID Only: 1. 53 Error - Replace memory card. have a peek at these guys Paper path rollers worn?

Replace fuser. 2. IIISi/4Si Only: 1. A SIMM memory error occurred. 5Si/4000/4050/4100/5000/8000/8100 Only: X= Hardware type. 0: Rom 1: Ram Y= Hardware device. 0: Internal memory 1: SIMM slot 1 2: SIMM slot 2 3: SIMM slot

Have questions or need help?

part# RM1-0013 purchase HP 4200 fuser/maintenance kit here for use in HP LaserJet 4200, HP LaserJet 4200N, HP LaserJet 4200TN, HP LaserJet 4200DTN, HP LaserJet 4200DTNs, HP LaserJet 4200DTNsl part# RM1-1082 X=1: Beam detect malfunction. 2. If the fuser does not turn on check SW101. 3. Perkins and Marjorie Kinnan Rawlings (1999) and Thomas Carlyle: Sartor Resartus (2000). Πληροφορίες βιβλιογραφίαςΤίτλοςSartor Resartus: The Life and Opinions of Herr Teufelsdröckh in Three BooksΤόμος 2 του The Norman and Charlotte

Wrong I/O cable. 3. I've read about folks "upgrading" their 4000 by installing a 4050 formatter, but not the other way round.Thanks for any suggestions you might be able to offer. Check Fan 3, replace if necessary. 4000/4050/4100/5000 only: 57.4 Printer Fan 57.7 Duplex Fan 8000/8100 only: 57.2 Fan 3 location: formatter 57.3 Fan 2 location: Low-voltage powersupply 57.5 Fan 1 location: check my blog Replace Cable, DC Controller to H.V.

HP LaserJet Error Codes and Service errors Back For additional help please Email our technical department Choose the error number from the menu below 02 11 12 12.x 13 13.x 14 DC Power Supply malfunction. 2686 Only: 1. Check PS701 and PS703 13.20/13.32 Paper stopped jam in paper path.