Home > Printer Error > Printer Error Reinsert Duplexer

Printer Error Reinsert Duplexer

Gently remove any jammed paper or bits of torn paper from the rollers inside the printer. Sign in Share More Report Need to report the video? Wait until the warm-up period finishes before you proceed. This error can occur if the driver you are using is not IEEE-1284 compliant. this content

The printer lights might flash, and the carriage might move. Wait until the warm-up period finishes and your printer is idle and silent before you proceed. Check that the accessory is properly seated on and connected to the printer, without any gaps between the printer and the accessory. Some settings might have been reset to the factory defaults. check here

Reconnect the power cord to the rear of the printer. Use only clean unused paper in the tray. Letter or A4 size paper on a flat surface to align the edges. No action necessary.

  1. Printing will continue as soon as it is done.
  2. Try removing and reinstalling the optional envelope feeder.
  3. For help press Product illustration alternates with To continue press Product illustration The printer received more data than can fit in its available memory.
  4. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting.
  5. Gain access to and clear paper jams through the rear of the printer whenever possible.
  6. Disable the write protection through HP Resource Manager.
  7. REPLACE CARTRIDGE To continue press Product illustration Pages remaining for this supply has reached the low threshold.
  8. Load the requested media into tray 1 and press Product illustration (Select button).
  9. If the error message persists, skip to the next solution.

Wait at least 60 seconds. The printer might report a paper jam even when there is no jammed paper. This message displays for 30 seconds, and then the product returns to a ready state. Use HP Web Jetadmin to initialize the file system.

and may not be used without advance written permission of PrinterTechs.com, Inc. While the printer is still on, disconnect the power cord from the rear of the printer. Disconnect the power cord from the rear of the printer.

If STAPLES OUT=CONTINUE, printing continues, but the job is not stapled.

The message continues while the job is stopped, the paper path is cleared, and any remaining incoming data on the active data channel is received and discarded. RAM DISK IS WRITE PROTECTED To clear press Product illustration alternates with The RAM disk is protected, and no new files can be written to it. Touch the Down Arrow () to scroll to Reports. Sign in Transcript Statistics 3,564 views 10 Like this video?

Loading... http://h30434.www3.hp.com/t5/Inkjet-Printing/HPEnvy-5535-reinserting-duplexer-cover-paper-roller-feeder/td-p/4607226 Make sure the toner cartridge is a genuine HP toner cartridge. Note: EIO 0 is reserved for the HP Jetdirect embedded print server. Remove any bits of paper or torn pieces of paper from the output tray rollers.

For the HP LaserJet 4350 series, the message first appears when about 25% (10,000-page cartridge) or about 15% (20,000-page cartridge) of the life remains in the print cartridge. http://spamdestructor.com/printer-error/printer-error-091-935.php Only one copy will be produced. Jimitron 5,711 views 4:13 HP Photosmart C7280 blank page fix - prints a blank page - Duration: 3:36. Press ...

Press the cloth against the external rollers, and then rotate them upward with your fingers. Thank you! Register ยท Log In HP Support Forum Home > Printers > Inkjet > HPEnvy 5535- reinserting duplexer cover/paper roller feeder ... caution: Remove paper from the tray as carefully as possible. have a peek at these guys Press Product illustration (Select button) to clear the error message. (The job will not be printed.) 40 EIO X BAD TRANSMISSION To continue press Product illustration The connection has been broken

Turn the printer power off, remove the EIO accessory from slot [X], install it in a different EIO slot, and then turn the printer power on. Repair fees might apply for out-of-warranty products. To solve this problem, simplify the print job or install additional memory.

Turn the printer power off.

If the message persists, contact an HP-authorized service or support provider. 41.3 UNEXPECTED SIZE IN TRAY X For help press Product illustration alternates with LOAD TRAY XX [TYPE][SIZE] To use another Look for and remove any obstructions along the far left side of the carriage path, such as paper or debris. caution: If the paper tears while you remove it from the rollers, more paper jams might occur. How do I print a Printer Status Report?

If the printer control panel message continues to appear, the optional hard disk needs to be replaced. INSTALL TRAY [X] The printer is unable to print the current job because the specified tray [X] is open or not inserted correctly 1. FLASH FILE OPERATION FAILED The requested operation could not be performed (for example, attempting to download a file to a nonexistent directory). 1. check my blog Use HP Web Jetadmin to initialize the file system.